Maintaining a high level of control over your piping system can be accomplished in an efficient and effective manner by combining an os&y gate valve with supervisory switch with a supervisory switch. However, in order to successfully install one, you need to keep a few things in mind at all times. These aspects include the kind of switch that you are utilizing, the number of times inspections are performed, and the degree to which the valve is open.
There are a few things that you need to be aware of before you press the install button, and this is true regardless of whether you are installing a brand new Supervisory Switch or upgrading to a new one. A Supervisory Switch is a device that monitors the operating condition of your valve. It does this in a supervised manner. In particular, it is an electronic device that, depending on the position of the valve, either engages or disengages the control rod. This device is typically mounted on the exterior of a valve same with os&y gate valve with tamper switch; however, it can be attached to some valves via an internal thread if the valve is designed appropriately.
You are going to need the appropriate tools in order to install a supervisory switch. A straight file with a diameter of 3/8 inches ought to be one of the tools you keep on hand. This device can be used to file a groove for the trip rod that is one eighth of an inch deep in the valve stem. It is recommended that the trip rod be installed as far away from the valve gland as is practically possible without coming into contact with the mounting plate.
You need to know how to test an OS&Y gate valve if you are going to operate a water-based fire protection system or an irrigation system. It is a pressure reducing screw and yoke valve located on the outside of the pipe that controls the flow of water. Control valves are the typical application for these valves, but they also have the capability of being electronically supervised.
It is important to perform routine inspections and tests on the os&y gate valve. It is essential to be able to differentiate between the open and closed positions of the valve, and a supervisory switch monitors the process of making this distinction. Tamper switches are an additional name for these types of devices. They provide the highest levels of dependability and precision.
A trip rod is housed inside a small box that serves as the supervisory switch. This box is attached to the valve stem. The trip rod is intended to be simple to manipulate and should be able to move freely in and out of the groove that is found in the valve stem. In addition to this, the length of the trip rod needs to be adjusted appropriately.
When it comes to an os&y gate valve with a supervisory switch, the frequency of inspections can vary quite a bit depending on the type of seal that is currently protecting the valve. Routine visual inspections guarantee that the valve is unaffected by any physical damage and that it continues to function properly. In contrast, electronic monitoring of the valve can cut down on the number of times it needs to be inspected.
The movement of the gate on an os&y gate valve, which is also referred to as an indicating gate valve, is what controls the flow of water. This results in a decrease in both pressure and flow. Control valves are one common application for these valves.
In order for an automatic fire sprinkler system to work properly, control valves are an absolutely necessary component. The flow of water into the fire sprinkler system is controlled by these valves. The primary control valve is typically mounted on a riser that is situated between the water main connection and the system's extensive piping network.
In most cases, control valves are inspected once per week. However, valves that have locks are required to have monthly inspections. In the event that the valve is not backed up, there is a possibility that the system will malfunction. From a fully opened position, it is recommended that the valve be turned counterclockwise by a quarter turn.
The formula for calculating friction loss from fittings can be found in Table 28.2.3.1.1 of the NFPA 13 standard. This is an essential piece of equipment for ensuring that your fire sprinkler system is operating as it should at all times. In addition, the Hazen-Williams C-factor that should be used for your dry nitrogen systems can be calculated with the assistance of this table.
Within a water-based fire protection system, there can be found a wide variety of valves. Electronic tamper switches, which are electronically monitored, are by far the most common type. When the valve is closed, these devices will emit an alarm and serve their purpose. In addition to this, the device sends a signal to a location that has someone present at all times. This results in fewer checks being performed overall.
In addition to that, it is required that certain sprinkler system valves be of the indicating-type valves. It is common practice to position these valves in areas that are not continuously monitored by personnel. The gate valve are the common name for these kinds of valves. These valves have a screw or stem that is threaded, and they have a gate that moves in a direction that is perpendicular to the flow of water. The handwheel is connected to the gate that is there.
The AFC Valve Factory guarantees that every single valve they produce will be able to pass hydrostatic testing. The shell test pressure rating is typically 1.5 times higher than the seat test pressure rating, which is 1.1 times higher. The pressure test for the seat is typically 1.1 times higher. As a result of the tests, we have full faith that every valve will perform as expected within the water system. As our standard, we have been following EN12266. The UL/FM testing procedure will be carried out on products that are up to the standards set by both UL and FM.
Each stage of production of the valves is subject to stringent quality control because a standard manufacturing procedure is used. Casting, machining, coating, assembly, testing, and packaging are just some of the processes that the quality control system at AFC has been monitoring with IPQA to ensure that each step is well controlled and recorded. A flawed end product may be the result of controlling the processes.
The design of this valve is the product of our team's combined experience of more than 30 years in the field, as well as extensive feedback from the field. On the job, our product is not only safer but also more effective. All valves are designed in accordance with a variety of different standards. It is possible to design the gate valve so that it complies with EN, AS, and UL standards. The butterfly valve with double embroidery are capable of meeting the requirements of both EN and AWWA. Each product has to live up to the expectations of its respective manufacturer.
The nation that has the most efficient supply chain is China. The castings represent the majority of the cost associated with the water gate valve. Castings of the highest quality are being manufactured in China at prices that are affordable. The quality of castings can be evaluated using a wide variety of different methods. When searching for a product that strikes the optimal balance between quality and cost, the AFC valve is the best option.
Copyright © 2022 Suzhou Alpine Flow Control Co., Ltd Privacy policy Terms and Conditions
EN 
ES
PT
SV
DE
TR
FR
